Step 4:How to make a cheating pen

step 4time to cheat

now rolling the tip of the pen make the paper go inside
and rolling the other side make the paper go out.
And all this things is hiding with your hands. 

Step 3:How to make a cheating pen

step 3Make sleeve in the pen

Make a sleeve about 1 1/8 inches on the base of the pen.
And slide your rolled paper into the pen.

Step 2:How to make a cheating pen

step 2The pen

Disassembly the pen and stick the end of your cheat paper to the ink stick.
Roll it tight.

Step 1:How to make a cheating pen

What will you need:
- an ordinary pen
- crafting knife(any kind of thing that is used for cutting)
- glue
- a piece of paper

step 1Paper cheat

cut a piece of paper about 1 inch wide and 3 inch long

Mark on this paper the answer you want to cheat.
(You can add more information on your paper if you write with computer and print it.) 

Step 4:How to make slime

Add any food coloring to the mixture if you wish. If not your slime will be plain.

Step 3:How to make slime

Put the mixture of glue and water into a bigger container and add the borax solution and mix them.

Step 2:How to make slime

Put all of the glue into a cup and make sure you put all of them and add water until the cup is full then mix them until they're completely mixed.

Step 1:How to make slime.

What will you need:
-borax
-water
-glue



Mix one tea spoon of borax and half cup of water until it mixed completely.

Step 10:How to make a simple water rocket

Fill your bottle between 1/2 way & 2/3. Pump the air pump to between 60 & 80 and launch! The air pressure on the top, to the balloon should bounce the top off on the way down, releasing the top and then your parachute. Watch as your tennis ball floats through the air!

Step 9:How to make a simple water rocket

Fold the parachute in half horizontally and then again vertically. Fold the parachute into vertical triangles. After it is the thinnest you can make it, fold it in half horizontally. Place the tennis ball, followed by the parachute in the bottom of the bottle rocket.

Step 8:How to make a simple water rocket

The balloon should be blown up to capacity (which isn't very big because it's a water balloon). After it is blown up, place it in the top of the cone.

Step 7:How to make a simple water rocket

Using your Exacto knife, cut a hole through the tennis ball. Take a piece of wire and loop it through the tennis ball so it creates a handle. Then take your parachute and put 8 pieces of masking tape, spread evenly around the edge. Then punch 8 holes, one in each piece of masking tape. Take your fishing line and cut 8 even pieces. Tie one end of the fishing line to a hole in the parachute and the other end to the handle on the tennis ball. Repeat 7 times. Make sure the fishing line is taut when you lift up the tennis ball in the center of the chute.

Step 6:How to make a simple water rocket

Take your garbage bag and cut the bottom off so that it lays out flat into a big rectangle. Then cut down the center so you have two squares. Cut a circle out of one of your squares, and there you have your parachute.

Step 5:How to make a simple water rocket

After creating the top, create 6 incisions using the Exacto knife, spread equally apart, around the top part of the cone. Then cut each elastic band so they are straight lines. Slide the rubber bands through the incisions. The first one through the first incision, and through the incision across from it; the second one through the second incision, and through the incision across from that; the third through the third incision, and through the incision across from that.

Pull both sides of the elastics up over the top of the bottle and screw on the top to hold in place.

An asterisk should appear in the inside of the top of your cone.

Step 4:How to make a simple water rocket

Creating the top of your rocket is really simple. All you have to do is take the top of the first bottle you cut and attach it to a foam cylinder using duct tape. Then take a piece of foam and place it under the top of the bottle. Trace the outside of the circle on the foam. Cut out the circle with the Exacto knife. Use the outside as a skirt and place it around the cylinder, attach using a stapler.

step 3:How to make a simple water rocket

Take the manila folder. Along the folded side, cut three triangles so when they are opened, they appear as diamonds. Fold the edges of the fins so there is a flat piece that will be taped down to the bottle. Attach the fins to the bottle using duct tape.

step 2:How to make a simple water rocket

Place the middle of the cut bottle on the bottom of the second bottle and attach using duct tape. Make sure the two pieces are securely attached.

Step 1:How to make a simple water rocket

What you will need
2 2L Bottles
1 Thin Garbage Bag
1 Manila Folder
2 Sheets of Arts & Crafts Foam
1 Water Balloon3 Rubber Bands1 Tennis Ball
Fishing Line
Scissors
Exacto Knife
Duct Tape
Masking Tape
Stapler/Staples
Wire

First, in this step you will have to use an Exacto knife to cut out the center of the first bottle. Look at picture to see where to cut. Make sure you keep the top and bottom leftover from cutting out the center.                                                                                                        

opening

Hi! Nice to meet u all ^ ^, in this blog we will learn to make many thing such as slime. This will be updated everyday except when i have test or something.